What did you do to your JK today?

[Reapertsm]

Alright. I will take your word for it.
This is all so overwhelming. I have been reading the forums for almost 2 months , every time I get something figured out someone says nope that’s not going to work.

Trying to do things right the first
Time, it seems like that isn’t possible.

Fair enough. Ive Never messed around with suspension on vehicles before so Its frustrating.

I was originally going to purchase the metalcloak 2.5 GC lift that comes with all the arms etc. Maybe I should go back to that plan.

Yes it is 4:10 gears on my unit.

I’m not into anything extreme, this jeep isn’t a daily driver, but I don’t trailer it to the trails either. Just want to armor up as
Much as possible , and I’ll be good on 35’s doing what I want to do.

I probably should have went all aluminum skid instead of the SB XRC . This stuff is so heavy.

Right now I’m on 285/70/17 and it operates fine. But I put a winch on it and in my opinion the front sags to much.

For the trails I drive , I want full skid and 35’s

Original reason for this post is I bought the SB XRC skids from a 4x4 shop who said they will fit. Apparently they do not and won’t accept a return. My bad for being ignorant and not knowing enough before hand. But learned a couple lessons in the process.

Might just cut my losses and go with a proper lift that has all the arms etc, trackbars etc. Every time I look into just a spacer lift someone says it’s going to cause problems.

Apparently MC 2.5 lift is upgradable to 3-4” if I need to go to that later.

Thank you for the info and your time.

 

[Reapertsm]

Just wanted to say thanks for the info about getting proper control arms. I’ve researched much more and spending the extra for a complete lift is the way to go. Well, it’s what I’m doing. Will post some pics when it’s done next week.

This 2018 rubicon recon is really a nice unit.

Thanks.

 

[mjonesjr84]

Mine lost and rebalanced weight. I ditched the large, heavy, and plugged up OEM muffler last week. I've driving it this week with just the resonator and it was too loud for me. I wound up installing a 4" round Magnaflow straight through muffler today. It sounds really good. When I removed the OEM muffler, I noticed a quick jump in fuel mileage. My only contribution to that was that it was the original muffler and it was clogged after 220k miles. Tomorrow, if I get a chance, it will lose a bit more weight by removing the heat shield.

 

[tJKrider]

Mine lost and rebalanced weight. I ditched the large, heavy, and plugged up OEM muffler last week. I've driving it this week with just the resonator and it was too loud for me. I wound up installing a 4" round Magnaflow straight through muffler today. It sounds really good. When I removed the OEM muffler, I noticed a quick jump in fuel mileage. My only contribution to that was that it was the original muffler and it was clogged after 220k miles. Tomorrow, if I get a chance, it will lose a bit more weight by removing the heat shield.

View attachment 128916

View attachment 128917

Have a sound file you can post with the Magnaflow installed??

 

[mjonesjr84]

Have a sound file you can post with the Magnaflow installed??

I can't figure out how to get the recording to post. Here is the link where I got the muffler idea from.

The picture is the part number.

 

[Danarch]

Yesterday picked up the wife’s Jeep finally from the clockspring being replaced. First dealer wanted us to authorize up to $800 for diagnostic said forget it. Second dealer said $235 for diagnostic but if clockspring no charge. They covered it all under the extended warranty. But they did want $900 for new brakes front and rear, needless to say I declined.

Took my Jeep for the biannual CA smog today, it passed as the CEL had come on for temperature not rising fast enough. It went off a few days ago so took it in.

While at the dealer ordered two t-stats hopefully they show up soon.

 

[JerryD]

Not all Rubicon's got 4.10 gears. I'd pull your VIN to verify.

I wouldn't put a lift on without adjustable control arms. Your ride, ground clearance, and alignment will be much better. Don't skip out.

I have to add, mine had the AEV 2.5" lift when I got the jeep at 22k miles. At 98k miles, here's my observation. It's got 3.73 gears &35s ‐ regear highly recommended but elevation and terrain play a big part... i plan on doing it, just hasnt been a priority. I'm done doing really technical trails so it's "okay" for me. Correction brackets have worked great, better than stock handling with no alignment issues. Slight loss in clearance, but really not much of an issue with the trails I do and driving technique. Just wanted to give personal experience with the AEV Correction brackets.

 

[Jskunk]

Nothing exciting but I've been putting it off forever. These crusty old battery terminals have been giving me hell for 2 years and I decided they had to go.

What an upgrade over OEM style.

The only complaint would be the allen key to tighten the new terminals is on the wrong side on the negative terminal and had to be rotated to mount into the recessed style battery post.

 

[Danarch]

Nothing exciting but I've been putting it off forever. These crusty old battery terminals have been giving me hell for 2 years and I decided they had to go.

What an upgrade over OEM style.

The only complaint would be the allen key to tighten the new terminals is on the wrong side on the negative terminal and had to be rotated to mount into the recessed style battery post.

View attachment 128927

View attachment 128928

View attachment 128929

I cut allen key down to fit in the little opening. It would be nice if it screwed in on the other side.

 

[trucker_mike]

Dropped it off at the off-road shop to get the front end upgraded and a new front drive shaft.

 

[Dirty Dog]

Ordered a new TIPM for Mrs. Dogs JKUR.

 

[mjonesjr84]

Installed the DV8 door pockets inplace of the cheap Amazon ones. These are much sturdier and mount much better. Now I need to find a good holster for my pew pew that will mount to the molle panel.

Also installed a flashlight mount to my seat. It was must laying beside the e-brake handle and was really in the way if I wanted to use the e-brake.

 

[mjonesjr84]

Installed the Hot Heads headliner and their sound deadening strips. The install was very easy. It only took me about an hour by myself from start to finish. Going to be interesting to see over the next couple of days how much improvement there is. I've got about 3-4 weeks before I pull the hard top and install the Bestop soft top.

 

[WSS]

I fixed my last dtc code Friday! P2096, bank 1 on a hemi is different from the oe engine. Once I figured that out, bingo. 5 o2 sensors later (don't ask why 5). My plan with this rig is to do one "essential" and one "optional" project at a time. So now the essential dtc problem is fixed, I fixed up my readywelder kit. I transferred the gun itself and all the hook up stuff to a new ATC recovery bag. This kit has been on three Jeeps so far. I used anderson connectors to jump two 12v batts to make 24v. The issue on this Jeep is the second battery is in the rear now. But my jumper cables have anderson connectors on them (i had a anderson quick connect on the front bumper of my CJ and TJ). The combo lets me reach from the fornt to rear without much loss of length.

In the kit are gloves, mask, auto darkening goggles, spare consumables, 8' anderson extension, jumper cable kit, mag ground, arm sleeves, welding hat, manual and 24v adaptor/connector.

 

[tJKrider]

I fixed my last dtc code Friday! P2096, bank 1 on a hemi is different from the oe engine. Once I figured that out, bingo. 5 o2 sensors later (don't ask why 5). My plan with this rig is to do one "essential" and one "optional" project at a time. So now the essential dtc problem is fixed, I fixed up my readywelder kit. I transferred the gun itself and all the hook up stuff to a new ATC recovery bag. This kit has been on three Jeeps so far. I used anderson connectors to jump two 12v batts to make 24v. The issue on this Jeep is the second battery is in the rear now. But my jumper cables have anderson connectors on them (i had a anderson quick connect on the front bumper of my CJ and TJ). The combo lets me reach from the fornt to rear without much loss of length.

In the kit are gloves, mask, auto darkening goggles, spare consumables, 8' anderson extension, jumper cable kit, mag ground, arm sleeves, welding hat, manual and 24v adaptor/connector.

View attachment 128984

View attachment 128985

View attachment 128986

View attachment 128987

Very cool! Have you had to use the Readywelder out in the wild yet??

 

[tJKrider]

Very cool! Have you had to use the Readywelder out in the wild yet??

@WSS do you just use flux core with that or carry a gas supply? Ever tried aluminum? Thx!

 

[WSS]

@WSS do you just use flux core with that or carry a gas supply? Ever tried aluminum? Thx!

I use flux core in particular Lincoln NR-211 in .030". Never tried aluminum, but it is a "spool gun". I have a miller spoolgun but no welder to power it. I have 4) dimenion 652's and 1) XMT 456, none of them are capable of running my spoolgun. I had big dreams of learning aluminum mig.

I have used it twice on the trail, once for a tie rod end and once for a shock mount, neither on my rigs. I like having that kind of stuff for some odd reason. The ReadyWelder can weld 1/2" plate easy enough with .035" and 3/8 with .030" double or triple pass. 1/4 like butter and looks good too.

 

[JerryD]

Okay, not necessarily done to my jk, but I use it with my JK and it's jk-adjacent,

Scored a set of Moab hikers. Friend of my daughter works for Wolverine World Wide and gets these not-for-resale samples. She saw these and thought of our family. I got to them before my son did . I've had three pairs of the low top shoes, and they've been great so I expect the same from these, but I don't have to pay the licensing fees.